When to Close Your Pool in Spokane, WA: Deadline, Window & Checklist

Spokane closing dates at a glance

A short season cuts both ways: every week opened before June 6 is a real slice of Spokane's roughly 70-day warm-swim budget.

The same model in water terms: Spokane's estimated pool temperature runs about 47°F in mid-April, 62°F in mid-June, 72°F in mid-August, and 52°F in mid-October, peaking near 73°F. Those four checkpoints — not any calendar holiday — are what the windows above are protecting.

The 12-step Spokane winterizing checklist

A closing is a plumbing project with a chemistry warm-up. Start a few days ahead of your target date, keep every dose per its product label, and don't skip the photographs — spring-you reassembles from them.

1. Balance the water a few days ahead

   Start midweek for a weekend close: bring alkalinity and pH into their label ranges and let the water settle. What you seal under the cover is what the pool soaks in until spring.

2. Deep-clean the pool

   Make the last cleaning the best one of the year: full skim, full brush, careful vacuum. Debris left behind steeps all winter and greets you as April's water problem.

3. Service the filter one last time

   Backwash sand or DE, or pull and rinse cartridges, per the manual. A filter stored dirty cakes over winter and starts spring half-clogged.

4. Apply winter chemicals per label

   Run the winter kit through moving water: dose each product per its label with the pump on, give it a few hours to distribute, then start the shutdown. Chemistry added to still water stays where it lands.

5. Lower the water level

   Take the level down only as far as the cover's manual says — usually just below the skimmer for solid covers, higher for many mesh systems. An empty pool is never the goal; shells crack and shift without water's weight.

6. Blow out the lines and plug returns

   Air through every line — skimmer, returns, cleaner — until each blows dry mist, plugging returns while the air still pushes. Nothing else on this list protects as much plumbing per minute.

7. Protect the skimmer

   The skimmer throat is where trapped water has no escape — park a guard bottle or rated plug in it and let ice crush the cheap part.

8. Add pool antifreeze where blowouts fall short

   Doubt is the criterion: any run you can't confirm dry gets pool-grade antifreeze at the label's per-foot rate. The automotive jug from the garage is for cars — it has no business in pool plumbing.

9. Drain the equipment

   Open the drains on everything that holds water and let the pad empty completely. Cartridges and small equipment overwinter far better on a garage shelf than outside.

10. Set the air pillow and cover

    Inflate the pillow to about two-thirds, center it, then bring the cover over and secure it per its design. Under ice, that soft dome is the difference between inward compression and outward wall pressure.

11. Shut down the heater carefully

    Follow the manufacturer's winterizing sequence for your heater — drain it fully and, for gas units, close the supply valve. Heat exchangers are the most expensive freeze casualty on the pad.

12. Stage the cover pump

    Solid covers need drainage all winter: set a cover pump or siphon before the first storm, not after. Standing water strains seams and invites a mid-winter emergency.

What to buy before the rush

The September crowd empties shelves in a predictable order. This is the short list worth owning before Spokane's window opens — nothing exotic, just the stuff everyone needs the same weekend.

• Winter cover

  Sized to overlap; the cheapest insurance the pool wears all winter.

• Cover pump

  Keeps rain and melt off a solid cover all season.

• Expansion plugs + skimmer guard

  Seals blown-out lines and sacrifices itself to skimmer ice.

• Pool antifreeze

  Pool-rated glycol for the lines air couldn't clear.

• Winter closing kit

  Closing chemistry in one box, dosed by pool volume.

• Air pillow

  Gives ice somewhere to push besides your pool walls.

How Spokane compares locally

Spokane closes in the earlier half of Washington's calendar. Neighbors run close: Spokane Valley (9 mi away) models its deadline at September 27 (the same day vs Spokane's September 27), while Coeur d'Alene (30 mi) shows September 26. The spring mirror of this page is the Spokane opening guide, and the season overview draws both windows on a single bar.

The instrument behind this page is Spokane Felts Field, 5.3 miles east of Spokane — the closest station publishing complete 1991–2020 daily temperature normals. Thirty years of its readings set every date above; your own yard adds or subtracts a degree with shade, wind, and pavement, which is what the window's width is for.

Field notes for Spokane owners

Match the drainage plan to the cover

Solid covers shed nothing — they need a cover pump staged before the first storm and checked after each one. Mesh covers drain themselves but pass silt that settles all winter. Either way, the plan is decided in October, not improvised in January when the cover is an ice sheet.

Gas heaters get the manual, not a guess

Every heater brand sequences its winterizing differently — drain plugs, blower considerations, gas supply, control settings. The generic advice (drain fully, close the valve) is right but incomplete; ten minutes with your model's manual protects the most expensive component you'll winterize.

Cold water is the whole point

A pool closed at 55°F barely changes all winter: algae are dormant, chemicals hold, and spring opens with a light dusting instead of a bloom. A pool closed at 72°F runs its own quiet ecosystem under the cover for a month. The date matters less than the water temperature it represents.

Closing for a real winter

A Spokane closing has to hold for months of freeze-thaw, not a few frosty mornings. Spend the effort where winters bite: prove every line dry, drain every vessel on the pad, guard the skimmer, and tension the cover for wind that will actually come. The reward is a spring opening that's a rinse, not a rebuild.